800-507-2338 | Mon - Fri 7:30a - 4:30p PST | Corona, CA
800-507-2338 | Mon - Fri 7:30a - 4:30p PST | Corona, CA
All fields are optional
Select Moto

Eibach - 2015-2020 Chevrolet Colorado 2WD/4WD

Product Releases - 2015-2020 Chevrolet Colorado 2WD/4WD


Our all NEW PRO-TRUCK COILOVER 2.0's are here! Developed utilizing our extended-travel monotube design and variable force valving, Eibach PRO-TRUCK COILOVER 2.0 delivers control during on-road transit and compliance for maximum traction on the trails. Designed for use with our championship winning ERO Off-Road Race Springs, this system allows for various combinations to fine tune ride height and load capacity from fully loaded crawlers to factory weight vehicles.

  • Utilizes ERO springs manufactured using race winning off-road spring technology
  • Adjustable ride height allows adjustment of up to +3.0" on the Colorado
  • Pre-assembled for direct bolt-on installation, out of the box height is set to match the rear height
  • Designed to work with factory control arms for an increase in height without accelerated wear to ball joints and bushings
  • Developed specifically to provide a balanced ride quality on and off-road
  • Made by Eibach in the USA
  • 2 - Front Coilover Threaded Body Shocks
  • 2 - Front Eibach Race Springs
  • 2 - Billet Aluminum Top Mount
  • 2 - Billet Aluminum Spring Perches
  • 2 - Polyurethane Elastomer Bump Stops
  • 1 - 6mm Adjustment Tool
  • All Required Mounting Hardware

Ride Height:
Front: +1.00 - 3.00"

Chevrolet Colorado 2WD/4WD Pro Truck Coilover 2.0
Chevrolet Colorado 2WD/4WD Pro Truck Coilover 2.0


Built upon decades of off-road racing victory, the Eibach PRO-TRUCK-LIFT combines a series of PRO-LIFT-KIT springs and PRO-TRUCK Sport shocks to create a perfectly tuned suspension system engineered for both, on and off-road performance.

Each PRO-TRUCK-LIFT is designed and tested to deliver maximum ride height without compromising the integrity of factory bushings, ball joints and other components.

With the same spring technology found in our ERO off-road race springs, the block resistant PRO-LIFT-KIT springs can be taken to the limit mile after mile ensuring consistent performance and ride height. Matched with our heavy duty PRO-TRUCK Sport shock system, this combination is capable of handling anything in its path. Precision shock valving allows compliance over large obstacles and control through rough terrain while also improving on road comfort and performance.

Ride Height:
Front: +2-3" / Rear: Can accommodate up to a +0-1.5" lift

Chevrolet Colorado 2WD/4WD Pro-Truck Lift System


Eibach PRO-LIFT-KIT springs are designed to provide a suspension lift for your Colorado without the use of coilover systems or spacer lifts. Eibach spring lifts allow full range of suspension travel without additional stress on bushings and ball-joints as seen with spacer lift systems.

Each PRO-LIFT-KIT is engineered and manufactured using the same technology found in our championship winning ERO Off-road race springs and carefully tested to provide unparalleled ride quality and off-road capability.

Ride Height
Front: +2.0"

Note: PRO-LIFT-KIT Springs must be used with Eibach PRO-TRUCK Sport front shocks, +2.0 inches of lift is acquired at the bottom Eibach shock clip with no added weight.

PRO-TRUCK Sport Shocks

PRO-TRUCK Sport front shocks offer 2" of adjust ability for the Colorado (when using factory springs) while rear non-adjustable shocks can accommodate up to a +1.5" lift allowing you to go with a bigger wheel and tire combo and clear most obstacles on the trail. Unlike "spacer" type lifts, the Eibach PRO-TRUCK Sport Leveling Shocks are designed to maximize all available wheel travel for a smoother ride when the "Going Gets Tough"!

  • Height adjustable spring perch grooves allows you to adjust the level of the spring seat to lift the front up to +2.0" (when using factory springs)
  • Monotube Design, 46mm Pistons, Nitro-Coated Rods and Heavy Duty Zinc Coating
  • Improved Handling & Stability—On or Off-Road
  • Individually dyno tested for matched performance
  • Easy—Direct Replacement Installation
  • Engineered and manufactured by Eibach in the USA

Ride Height
Front: +0-2" ride height adjustable when using factory springs / Rear: Non-adjustable, can accommodate up to a +1.5" lift


  • 1" Billet aluminum black anodized blocks
  • Includes u bolts and hardware
  • Zinc coated hardware to prevent rust
  • Sold as a pair
  • Made in the USA

Ride Height
Front: +1.0"

Before & After



Product Part # Front Rear MSRP Cart
This category is empty.
Loading Page Loading Your Parts